Frantic Stamper Happenings: Nativity Pop-up Card (Jen Carter)

This year, on the 25th of every month, we plan to share a Christmas card with you. We hope doing so will inspire you to create a card, too, along with each of us and get a head start on your Holiday cards!

So today, we offer you this FABULOUS card and tutorial from Jen Carter.

Nativity Pop-Up Card

by Jen Carter

When I first laid my eyes on the Frantic Stamper Nativity Creche & Sheep die set I knew I had to have it! I have had an idea on a way to use it for a long time but it wasn't until recently that I finally took the time to play around with the design. After a lot of readjusting I got the result that I wanted and I'm excited to share it with you today! I've also included a photo tutorial at the end of this post in case you'd like to replicate this idea.

As you can see in the photo above, I used the nativity die to create a pop up card. I love the results! I really like how the focus of the card is on the nativity.

Here's a closeup of Mary & Joseph. I used strips of washi tape to highlight them as they pray over Baby Jesus. I'll show you how I achieved that below.

This is the inside of the card. To hide where I had cut out the nativity from the back side of the card I cut a matching piece of cardstock to the same dimensions as the card and adhered it so you can still write a message inside.

And here's the back of the card. You can see where the nativity was cut out of the backside and how the piece that I adhered on the inside also helps stabilize the card.

Here's a tutorial on how I put this card together.

First I cut my cardstock to 4 1/4 x 11 (I could have cut it shorter because I end up trimming it later, but this made it easier at the time to get my measurements right). Then I scored it at 2 3/4". This is the line where I will line up my die.

I then chose 2 pieces of thick washi tape. It's best if your tape is the same width of Mary & Joseph so I found that my skinnier tape didn't work as well. The tape I used was 3/4" wide. I used my die as a guide to where I should place my washi tape on the cardstock as shown.

I lined up the die on the scored line and then placed the cutting plate on my die cut machine just above the bottom of the die so that I wouldn't cut the shape completely out. I wanted the bottom of the nativity to still be attached to my card so that it could pop up. By placing my cutting plate above the bottom of the die, when I run it through my machine it will only cut to where I have my plate, leaving the bottom portion intact.

This is what it looks like after I ran it through my die cut machine. You can see that it didn't cut the bottom of the nativity.

I removed the negative pieces of the die and then carefully peeled off any washi tape that was on the shape that I didn't want on my card. You can see how the tape goes farther down on my figures and over on to baby Jesus.

I took a very sharp pair of pointed scissors and gently used the tip like a knife to cut the tape in the places where I didn't want it, careful not to cut the cardstock in the process. Most of those places were almost cut for me because of the details that are already cut into the shape with the die, I just had to add a few slices here and there.

After gently peeling away the pieces that I had just cut with the tip of my scissors, this is what I had.

Now I trimmed the back side of the cardstock so that it was the same size as the front.

After trimming, this is what the card looks like when it is standing up. I tried to get my card to be about the same size as a normal card once it was cut and the star was attached but it ended up a little long. The front of this card measures 4 1/4" x 5 3/4". If I made this again, I'd adhere the star just a tad lower so it would fit in a regular sized envelope.

The inside/backside looks like this. To give it added stability to support the popped up nativity and to allow a place to write a greeting on the inside (which also "cleans up" the inside) I cut a piece of matching cardstock to place inside of the card (as shown on my card sample at the top of this post).

To the very top of the nativity, I added the Northern Star, cut out with gold glitter paper, and attached with a glue dot. I also cut out the Script Merry Christmas in Silver Metallic paper to finish off the card.

One more thing before I go. Did you know that Frantic Stamper now has a Flickr gallery!? We'd love to see what you've been creating using the Frantic Stamper Exclusive Precision dies! You can join the group and see what others have been creating or you can upload your own creations by clicking here.